Shenzhen JHA Technology Co., Ltd is one of the leading manufacturers of hardened Ethernet, PoE, and fiber connectivity products specifically designed for harsh and demanding environments.


  • 1(68).jpg
  • 2(57).jpg

16E1 to 4FE GFP interface Converter JHA-CE16F4

    • Transparent transmission of Ethernet data in 1 to 16 E1 circuits;
    • Can be equipped with four Ethernet switching electrical interface for the user to save an Ethernet switch;
    • Ethernet 10/100M, full/half duplex fully adaptive, support VLAN protocol;
    • Each port supports Ethernet support AUTO-MDIX (crossover cable and straight-line adaptation);
    • Ethernet interface is also optional optical interfaces to achieve optical Ethernet data transmission through the interconnection E1 far;
    • 16-channel E1 lines, the maximum delay difference between any two can reach 220ms; when the delay difference over 220ms, the delay will produce poor overrun alarm, while business interruption;
    • Built dynamic Ethernet MAC address list (4096), with local data frame filtering function;
    • Timer mode, the optional local timing and tracking E1 line timing, E1 line timing source can be automatically switched according to the signal quality. Such as E1 line timing source system for the first Road E1, when the first E1 failure (serious warning
    • Compliance with ITU-T standard protocol, GFP-F encapsulation suggestion G.7041, VCAT virtual concatenation and LCAS Link Capacity Adjustment recommendation G.7042, Ethernet mapping to nxE1 recommendation G.7043, Ethernet to single E1 map suggestion G. 804
    • When transmission bandwidth increases, will not damage the Ethernet data; transmission bandwidth is artificially reduced, it can also be realized without damaging the Ethernet data network;

    32 (2)


PDH/Voice Multiplexer

Interface converters

Ethernet to E1 Converter

  • 16E1 to 4FE GFP interface Converter JHA-CE16F4


    The device using reverse direction multiplexing technology to bundle for multiple E1 circuits to transmit the Ethernet data of 4Channel 100BASE-TX.It can realize conversion between 1~16 channel E1 and Ethernet optical interface, to make E1 channels interconnected with Ethernet optical interface. Using GFP encapsulation, support the LCAS (link capacity adjustment scheme) and LAPS protocol.

    This device can support 1-16Channel E1 channel configuration, can automatically detect the number of E1 and select the E1 available. It allows E1 lines transmission time, 1channel/4channel/8channel/16channel Ethernet bandwidth is1984Kbit/s, 7936Kbit/s, 15872 Kbit/s,31744Kbit/s.
        The device provides alarm function. The work is reliable and low power consumption, high integration, small size. Support Network management , The main function of network management system is to fulfill the inquiry for local and remote devices and configuration management including inquiry of alarm status on E1 line, Ethernet working status, and loopback control etc.

    Product Photo


    19inch 1U


    • E1 tributary ends may not correspond by serial connection;
    • When a single slip direction E1 fails, the other direction can still work;
    • E1 signal loop back and cut off the automatic detection function: When detecting the occurrence of a road E1 signal loop, the system cut off this E1; loopback released, E1 automatic recovery use this road;
    • Complete alarm indication, choose to display local / remote alarm;
    • Supports remote E1 line side loopback function to facilitate the testing of E1 lines;
    • Support local system for the remote system reset;
    • provide remote interface loopback command, easy to line maintenance;
    • Console management interface provides for easy installation opening;
    • Configuration network management module, support independent SNMP network management;
    • with this end in view the working status of remote device display function;
    • Multiple power mode options: AC220V, DC-48V / DC24V and the like;
    • DC-48V / DC24V power supply with automatic polarity detection function, when installed without distinction between positive and negative.



    ♦ E1 Interface

     Interface Standard: comply with protocol G.703;
      Interface Rate: n*64Kbps±50ppm;
       Interface Code: HDB3;

    E1 Impedance: 75Ω (unbalance), 120Ω (balance);

    Jitter tolerance: In accord with protocol G.742 and G.823

    Allowed Attenuation:     0~6dBm


    ♦ Ethernet interface(10/100M)

    Interface rate:  10/100 Mbps, half/full duplex auto-negotiation

    Interface Standard:      Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)

    MAC Address Capability:  4096

    Connector:      RJ45, support Auto-MDIX


    ♦ Working environment

    Working temperature:    -10°C ~ 50°C

    Working Humidity:     5%~95 % (no condensation)

    Storage temperature: -40°C ~ 80°C

    Storage Humidity: 5%~95 % (no condensation)



    Model Model Number:JHA-CE16F4
    Functional Description 16E1/4*FE Converter , Ethernet can be divided into logical isolation , Encapsulated with GFP package, support LCAS and LAPS protocol,support independent SNMP network management;
    Port Description 16*E1 interface;4 *FE Interface,one Console interface,one SNMP interface
    Power Power supply: AC180V ~ 260V;DC –48V;DC +24VPower consumption: ≤10W
    Dimension Product Size: 19 inch 1U 485X138X45mm (WXDXH)
    Weight 3.0KG



    32 (2)

previous page

next page

previous page

next page

Product consultation

Submit a message

*Note: Please fill in the information accurately and keep the communication unblocked. We will contact you as soon as possible

Related products